What Roof Coating and Waterproofing Actually Accomplishes
Roof coating is frequently misunderstood as a cosmetic product that makes a roof look better without substantively changing its performance. When a quality coating system is applied correctly over an adequately prepared and fully repaired surface, the reality is quite different. A properly installed elastomeric coating creates a continuous, flexible, seamlessly bonded waterproofing layer that protects the existing roofing system from UV degradation, thermal cycling, and moisture infiltration in ways that extend the roof's effective service life by a measurable margin.
The key distinction between a coating that delivers real performance and one that simply delays problems is the preparation and repair work that precedes the application. A coating applied over unsealed seams, deteriorated flashings, active blistering, or standing water conditions will fail at those same locations regardless of the quality of the coating product itself. Our approach in Burlington, KS addresses every identified deficiency before any coating material is touched, so the product is protecting a sound, functional roofing system rather than attempting to compensate for underlying problems.
Elastomeric roof coatings work because they combine high elongation properties with strong adhesion to the substrate beneath them. As the roofing system expands and contracts with temperature changes, the coating moves with it rather than cracking. This flexibility is particularly valuable on metal roofing systems where thermal movement is substantial, and on flat membrane systems where minor substrate movement would crack a rigid product but passes harmlessly through an elastomeric one. The result is a coating that maintains its waterproofing integrity through the seasonal stress cycles that challenge less flexible alternatives.
Beyond waterproofing performance, reflective roof coatings offer a meaningful thermal benefit for buildings in warm climates or with large flat roof areas exposed to direct sun. White and light-colored elastomeric coatings reflect a high percentage of solar radiation that would otherwise be absorbed by a dark membrane surface and transferred as heat into the building below. For commercial buildings and multi-family properties in Burlington, KS, this can translate into measurable reductions in cooling system load and energy consumption during warm months.
Elastomeric Acrylic
Water-based, highly reflective coatings with excellent elongation for flat and low-slope roof surfaces. Environmentally friendly application and easy recoat capability when maintenance is needed.
Silicone Coatings
Superior ponding water resistance compared to acrylic alternatives. Ideal for flat roofs with marginal drainage where standing water is a recurring condition. High UV stability over long term.
Metal Roof Coatings
Rust-inhibiting primers paired with flexible topcoats engineered for the high thermal movement of metal panel and standing seam roofing systems. Restores reflectivity and seals seams.
Polyurethane Coatings
Two-component systems offering superior abrasion resistance for high-traffic rooftop areas. Higher build rate achieves required film thickness in fewer coats than acrylic systems.
Modified Bitumen Coatings
Asphalt-compatible coatings formulated for use over modified bitumen and built-up roofing systems, providing UV protection and waterproofing reinforcement to existing asphalt surfaces.
Reflective Cool Roof Systems
High-reflectance, high-emittance coating systems designed to meet cool roof standards and reduce building cooling loads through solar reflectance ratings of 0.80 and above.
The Roof Coating Process at a Glance
Full Inspection
Every surface component assessed before any work begins
Surface Cleaning
Contaminants removed to achieve proper coating adhesion
Repair All Defects
Seams, flashings, and blisters corrected before coating
Primer Application
Compatible primer applied to ensure coating bond strength
Coating Application
Applied at specified coverage rate to achieve correct film thickness
Key Benefits of Professional Roof Coating and Waterproofing
-
Reflective Surface Reduces Building Cooling Load White and light-colored elastomeric coatings reflect a high proportion of solar radiation rather than absorbing it as heat. For buildings in warm climates or with large flat roof areas, this reflectance directly reduces the thermal load on the HVAC system and can lower cooling energy costs during peak summer months.
-
Seamless Coverage Eliminates Lap Joint Vulnerability Unlike membrane systems with overlapping seams at every panel width, an elastomeric coating applied in liquid form cures into a continuous monolithic surface without seams. This eliminates the lap joint failure points that are among the most common sources of flat roof leaks in membrane systems.
-
Lower Cost Than Full System Replacement For roofing systems with structurally sound membranes or metal panels that have developed surface degradation or seam issues, coating provides a cost-effective path to extended service life at a fraction of the cost of full replacement. The savings are most significant on large commercial roof areas where replacement involves substantial material and labor expense.
-
Ponding Water Resistance With Silicone Systems Silicone roof coatings maintain their integrity and adhesion even when submerged in standing water for extended periods, making them the coating of choice for flat roofs where drainage limitations result in occasional or chronic ponding. Acrylic coatings degrade under prolonged water contact, making product selection critical for these applications.
-
Recoatable System for Long-Term Maintenance Most elastomeric coating systems can be recoated when the original application has weathered to the point of reduced performance, typically after 10 to 15 years depending on the product and exposure conditions. Recoating restores reflectance and waterproofing performance at lower cost than either replacement or full reapplication, creating a long-term maintenance pathway for the roofing system.
-
Manufacturer Warranty on Coating System Performance Quality coating products applied by qualified contractors at specified coverage rates qualify for manufacturer-backed performance warranties that provide documented assurance of the system's waterproofing performance for a defined period. We apply coatings to manufacturer specifications and provide all documentation required for warranty registration.
Our Roof Coating and Waterproofing Process in Detail
We inspect the full roof surface to assess the existing membrane or panel condition, identify all deficiencies requiring repair, evaluate drainage performance, and determine the appropriate coating system for the application. System selection accounts for the substrate type, traffic requirements, climate exposure, and any ponding water conditions that may influence which product chemistry is most appropriate.
The entire roof surface is cleaned to remove dirt, biological growth, loose material, oils, and any previous coating that is not firmly adhered. Coating adhesion is directly dependent on surface cleanliness, and contaminants left beneath the new coat will cause delamination at those locations regardless of the product quality. Cleaning method is selected based on the substrate type and contamination level present.
Every deficiency identified during the initial inspection is repaired before any coating is applied. Lap seams are re-bonded or sealed, blisters are cut open and re-adhered, flashing terminations are re-secured and sealed, and penetration details are reinforced with compatible membrane material. The coating system is then applied over a fully functional, defect-free roofing surface.
High-stress areas including seams, flashings, penetrations, drains, and perimeter terminations receive an additional layer of reinforcement using compatible polyester or fiberglass mesh tape embedded in the base coat. This reinforcement layer bridges any residual movement at these transition points and prevents the coating from cracking at locations where the substrate is most likely to experience differential movement.
The coating is applied in the number of coats and at the coverage rate specified by the manufacturer to achieve the minimum dry film thickness required for performance and warranty qualification. We track material consumption against the calculated roof area to verify correct coverage. Final cure inspection confirms uniform film thickness, proper detail integration, and correct drainage flow with the new surface in place.
Frequently Asked Questions About Roof Coating and Waterproofing
Acrylic and silicone are the two most commonly specified elastomeric roof coating chemistries, and they have meaningfully different performance profiles that make each more appropriate for different situations. Acrylic coatings are water-based, low-VOC products with excellent UV resistance, high reflectance, and good adhesion to a wide variety of substrates. They are cost-effective and widely available, but their primary limitation is performance under sustained water contact. Acrylic coatings soften and can re-emulsify when submerged in standing water for extended periods, making them unsuitable for roofs with chronic ponding. Silicone coatings are solvent-based products that cure into a permanently hydrophobic surface unaffected by ponding water, even for extended periods. They maintain their reflectance and adhesion under ponding conditions where acrylics would degrade. The trade-offs with silicone include a higher initial cost, VOC concerns during application requiring appropriate ventilation, and the fact that silicone surfaces attract airborne dirt more readily than acrylics, which can reduce effective reflectance over time without periodic cleaning. The right choice for your roof depends on its drainage performance and the specific conditions it faces.
Surface rust on metal roofing can be addressed as part of a coating project, but the approach depends on the severity of the corrosion. Light surface oxidation that has not penetrated deeply into the metal panel can be wire-brushed and treated with a rust-inhibiting primer before the coating is applied. This stabilizes the surface corrosion and prevents it from progressing beneath the new coating. However, deep rust pitting, through-thickness corrosion, or areas where the metal has become structurally compromised cannot be resolved by coating alone and require panel replacement before a coating system can be effectively applied. We assess the rust condition during our inspection and provide an honest evaluation of which areas can be treated in place versus which require panel work before coating proceeds. Attempting to coat over severely deteriorated metal produces short-lived results because the rust continues to expand beneath the coating, causing it to blister and delaminate from the affected areas regardless of the coating quality applied over it.
The decision between coating and replacement for a flat roof comes down to the condition of the existing membrane and the insulation beneath it. A membrane that retains structural integrity, remains adequately adhered to the substrate, and has not allowed moisture to saturate the insulation is a coating candidate even if its surface shows significant weathering, chalking, or minor cracking. A membrane that is delaminating from the substrate in multiple areas, that has allowed water to penetrate into and saturate the insulation beneath it, or that has been coated previously and cannot accept another coat without proper preparation, may be better served by replacement. Moisture scanning of the insulation layer provides objective data on how much of the existing system has been compromised by water intrusion. We conduct this assessment and explain the findings clearly so you understand the actual condition of your roof and can make an informed decision rather than relying on a general impression of its surface appearance.
Extend Your Roof's Life With Expert Coating
One of the most economical methods to safeguard and prolong the life of a Burlington, KS business or residential roof is to have a roof coating system professionally done. By adding a smooth protective layer, it can lessen leaks, reflect sunlight, increase energy efficiency, and slow down UV and rain-related deterioration. Along with a maintenance and application schedule, a professional inspection aids in identifying present problems and determining if coating is appropriate. Demand a transparent plan and an honest evaluation.
1 (855) 481-3970Schedule Your Coating Assessment